#include <string.h>
#include <Arduino.h>
#include <SPI.h>
#include <Adafruit_NeoPixel.h>
#include "Adafruit_BLE.h"
#include "Adafruit_BluefruitLE_SPI.h"
#include "Adafruit_BluefruitLE_UART.h"

#if SOFTWARE_SERIAL_AVAILABLE
  #include <SoftwareSerial.h>
#endif

#include "BluefruitConfig.h"

#define BT_SCAN_MS 200
#define MINIMUM_FIRMWARE_VERSION   "0.7.0"
#define FACTORYRESET_ENABLE 1
#define DIM_FACTOR          50

Adafruit_BluefruitLE_SPI ble(BLUEFRUIT_SPI_CS, BLUEFRUIT_SPI_IRQ, BLUEFRUIT_SPI_RST);

void bluetooth_setup(){
  if ( !ble.begin(VERBOSE_MODE) ) {
    Serial.println(F("Couldn't find Bluefruit, make sure it's in CoMmanD mode & check wiring?"));
    while(1); // halt
  }
  if ( FACTORYRESET_ENABLE ) {
    if ( ! ble.factoryReset() ){
      Serial.println(F("Couldn't factory reset"));
      while(1); // halt
    }
  }
  if ( !ble.isVersionAtLeast(MINIMUM_FIRMWARE_VERSION) ){
    Serial.print(F("Callback requires at least"));
    Serial.println(F(MINIMUM_FIRMWARE_VERSION));
    while(1); // halt
  }
  pinMode(BLUEFRUIT_SPI_IRQ, INPUT_PULLUP);
  //ble.echo(false); // disable command echo
  //ble.verbose(false); // disable debug info
  ble.sendCommandCheckOK(F("AT+GAPDEVNAME=Suit LEDs")); // Change name displayed in bluetooth scans
  
  //ble.info();
  ble.setConnectCallback(on_connect);
  ble.setDisconnectCallback(on_disconnect);
  ble.setBleUartRxCallback(BleUartRX);
  ble.setMode(BLUEFRUIT_MODE_DATA);
}

void on_connect(void){
  Serial.println(F("Bluetooth Connected"));
}
void on_disconnect(void){
  Serial.println(F("Bluetooth Disconnected"));
}

void BleUartRX(char data[], uint16_t len){
  Serial.print( F("[BLE UART RX] " ) );
  Serial.write(data, len);
  Serial.println();
}

uint32_t pack_color(uint8_t r, uint8_t g, uint8_t b) {
  return ((uint32_t)r << 16) | ((uint32_t)g <<  8) | b;
}
uint32_t pack_color(uint8_t r, uint8_t g, uint8_t b, uint8_t w) {
  return ((uint32_t)w << 24) | ((uint32_t)r << 16) | ((uint32_t)g <<  8) | b;
}

class Strip {
  private:
  uint8_t pin;
  uint8_t num_pixels;
  uint16_t wait;
  unsigned long last;
  uint8_t offset;
  Adafruit_NeoPixel pixel;

  public:
  Strip(uint8_t led_pin, uint8_t strip_len, uint16_t wait_ms) {
    pin = led_pin;
    num_pixels = strip_len;
    wait = wait_ms;
    last = millis();
    offset = 0;
    pixel = Adafruit_NeoPixel(num_pixels, pin, NEO_GRBW + NEO_KHZ800);
  }

  public:
  void off(){
    Serial.println(F("off()"));
    pixel.begin();
    for(uint8_t i=0; i<num_pixels; i++){
      pixel.setPixelColor(i, pack_color(0,0,0));
    }
    pixel.show();
  }

  private:
  void rainbow(){
    uint8_t r = 255;
    uint8_t g = 0;
    uint8_t b = 0;
    pixel.begin();
    for (uint8_t index=0; index<num_pixels; index++){
      uint8_t loc;
      if (offset + index > num_pixels - 1){
        loc = index + offset - num_pixels;
      } else {
        loc = offset + index;
      }
      pixel.setPixelColor(
        loc,
        pack_color(r/DIM_FACTOR, g/DIM_FACTOR, b/DIM_FACTOR)
      );
      if (index < 24){ // red -> yellow shifting
        g += 10;
      } else if (index < 48){ // yellow -> green shifting
        if (index == 24){
          g = 255;
        }
        r -= 10;
      } else if (index < 72){ // green -> cyan shifting
        if (index == 48){
          r = 0;
        }
        b += 10;
      } else if (index < 96){ // cyan -> blue shifting
        if (index == 72){
          b = 255;
        }
        g -= 10;
      } else if (index < 120){ // blue -> magenta shifting
        if (index == 96){
          g = 0;
        }
        r += 10;
      } else { // magenta -> red shifting
        if (index == 120){
          r = 255;
        }
        b -= 10;
      }
    }
    pixel.show();
  }

  public:
  void update(){
    unsigned long now = millis();
    if (now - wait > last){
      last = now;
      rainbow();
      offset += 1;
      if (offset == num_pixels){
        offset = 0;
      }
    }
  }
};

Strip strip = Strip(6, 144, 100);

void setup(void) {
  //strip.off()
  while (!Serial); // required for Flora & Micro
  Serial.begin(115200);
  bluetooth_setup();
  Serial.println(F("Ready"));
}

void loop(void) {
  ble.update(BT_SCAN_MS);
  strip.update();
}